? coilcraft, inc. 2008 specifications subject to change without notice. please check our website for latest information. chip inductors C 0805hq series (2012) document 197-1 document 197-1 revised 10/06/08 1. when ordering, specify tolerance , termination and packaging codes: 0805hq-51nx jlc tolerance: g =2% j = 5% (table shows stock tolerances in bold.) termination: l = rohs compliant silver-palladium-platinum-glass frit. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). packaging: c =7 machine-ready reel. eia-481 embossed plastic tape (2000 parts per full reel). b = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter c instead. d =13 machine-ready reel. eia-481 embossed plastic tape. factory order only, not stocked (7500 parts per full reel). 2. inductance measured using a coilcraft smd-a fixture in an agilent/ hp 4286 impedance analyzer with coilcraft-provided correlation pieces. 3. tolerances in bold are stocked for immediate shipment. the 0805hq series offers our highest q factors in an 0805 form factor. in addition, current handling has been improved with significantly lower dcr values. like all coilcraft wire wound ceramic chip inductors, the 0805hq series provides exceptional srfs, tight induc- tance tolerance and batch consistency. for even higher qs, consider our surface mount spring inductors that combine the high q of an air wound coil with the convenience of automatic placement. coilcraft designer?s kit c325 contains samples of all 5% inductance tolerance parts. to order, contact coil- craft or visit http://order.coilcraft.com . inductance 2 percent srf min 5 dcr max 6 i rms 7 color part number 1 (nh) tolerance 3 q min 4 (ghz) (ohms) (a) code 0805hq-2n5x_l_ 2.5 @ 250 mhz 5 80 @ 1500 mhz 10.30 0.020 1.6 black 0805hq-5n6x_l_ 5.6 @ 250 mhz 5 98 @ 1500 mhz 6.10 0.035 1.6 brown 0805hq-6n2x_l_ 6.2 @ 250 mhz 5 88 @ 1000 mhz 4.75 0.035 1.6 red 0805hq-12nx_l_ 12 @ 250 mhz 5 80 @ 1000 mhz 3.00 0.045 1.6 orange 0805hq-16nx_l_ 16 @ 250 mhz 5,2 72 @ 500 mhz 2.95 0.060 1.5 yellow 0805hq-18nx_l_ 18 @ 250 mhz 5,2 75 @ 500 mhz 2.55 0.060 1.4 green 0805hq-20nx_l_ 20 @ 250 mhz 5,2 70 @ 500 mhz 2.05 0.055 1.4 blue 0805hq-27nx_l_ 27 @ 250 mhz 5,2 75 @ 500 mhz 2.00 0.070 1.3 violet 0805hq-30nx_l_ 30 @ 250 mhz 5,2 65 @ 500 mhz 1.95 0.095 1.2 gray 0805hq-39nx_l_ 39 @ 250 mhz 5,2 65 @ 500 mhz 1.60 0.110 1.1 white 0805hq-48nx_l_ 48 @ 200 mhz 5,2 65 @ 500 mhz 1.40 0.095 1.2 black 0805hq-51nx_l_ 51 @ 200 mhz 5,2 65 @ 500 mhz 1.40 0.120 1.0 brown 4. q measured using an agilent/hp 4291a with an agilent/hp 16193 test fixture. 5. for srf less than 6 ghz, measured using an agilent/hp 8753d network analyzer and a coilcraft smd-d test fixture. for srf greater than 6 ghz, measured using an agilent/hp 8722es network analyzer and a coilcraft smd-d test fixture. 6. dcr measured on a cambridge technology micro-ohmmeter and a coilcraft ccf840 test fixture. 7. current that causes a 15c temperature rise from 25c ambient. 8. ambient temperature range: ? 40c to +125c with i rms current +125c to +140c with derated current 9. storage temperature range: component: ? 40c to +140c packaging: ? 40c to +80c 10. resistance to soldering heat: three reflows at >217c for 90 seconds (+260c 5c for 20 ? 40 seconds), allowing parts to cool to room temperature between. 11. electrical specifications at 25c. 12. temperature coefficient of inductance: +25 to +125 ppm/c. refer to doc 362 ?soldering surface mount components? before soldering.
? coilcraft, inc. 2008 chip inductors 0805hq series (2012) specifications subject to change without notice. please check our website for latest information. document 197-2 document 197-2 revised 10/06/08 140 120 100 80 60 40 20 0 frequency (mhz) q factor 10 100 1000 5000 20 nh 30 nh 48 nh 2.5 nh 6.2 nh 16 nh 1 10 0 100 frequency (mhz) inductance (nh) 1000 5000 48 nh 30 nh 20 nh 6.2 nh 2.5 nh 16 nh 70 60 50 40 30 20 10 typical l vs frequency typical q vs frequency abcd max max max ref e f g h i j 0.090 0.068 0.060 0.020 0.050 0.020 0.040 0.070 0.040 0.030 i nches 2,29 1,73 1,52 0,51 1,27 0,51 1,02 1,78 1,02 0,76 mm a b overall f i i g d e terminal f j c h terminal wraparound: approx 0.015/0,38 both ends recommended land pattern weight: 10.5 ? 12.5 mg tape and reel: 2000/7 reel; 7500/13 reel 8 mm tape width for packaging data see tape and reel specifications section. irms derating -40 -20 0 20 40 60 80 100 140 120 ambient temperature (c) 120 110 100 90 80 70 60 50 40 30 20 10 0 percent of rated rms i 25c
|
